Nodegrid Gate Services Router - QSG - English
  • 25 Oct 2024
  • 3 Minutes to read
  • Dark
    Light
  • PDF

Nodegrid Gate Services Router - QSG - English

  • Dark
    Light
  • PDF

Article summary

Quick Start Guide for Nodegrid Gate SR

Security Warning

NodegridGate SR (GSR) provides extensive access to the devices attached to it. Precautions must be taken to avoid compromising your security policies.

From the factory, this equipment is shipped with the following settings:

  • DHCP, SSHv2, HTTPS – ENABLED

  • All Serial, USB, SFP+ and switch ports – DISABLED

  • Ethernet – ENABLED

Users will be required to create a password the first time they log in to the device.

Note: root access has been disabled for security reasons.

Please consult the Nodegrid User Guide for more information on security settings.

Please review the GSR Safety Information before installation.

GSR shown

GSR.png

1 Desktop or rack mount your GSR

For detailed rack mounting instructions, see the GSR User Guide.

SAFETY WARNING:

If the GSR is installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater than the room ambient temperature. Therefore, consideration should be given to installing the equipment in an environment compatible with the manufacturer’s maximum rated ambient temperature. For more information, see GSR Safety Statement.

2 Connect to your network

Connect a ZPE-recommended CAT 5e or CAT 6 cable from the 10/100/1000BaseT port to your network.

3 Connect to the Serial Console port

Using the ZPE’s RJ-45 console adaptor, connect a terminal or workstation to the serial console port on the GSR. The GSR will be configured using a terminal or terminal emulator with session settings of 115200 bps, 8, N, 1 no flow control.
Alternatively, use the HDMI port.

4 Connect power cables

Connect the power cables to the appliance.

5 Turn GSR on

Turn on the power switches.


Note: All remaining manual setup steps are required the first time you configure your GSR.

For manual downloads and support, visit: www.zpesystems.com/document-library/
For further assistance please contact ZPE Technical Support. support@zpesystems.com

6 Configure network parameters

NOTE: Skip to step 7 if you have a DHCP environment. DHCP is the default IP configuration. If no DHCP server is available, please log in to Nodegrid Gate SR via its console or HDMI port using admin credentials and configure a static IP address using CLI instructions as follows:

Text

[admin@nodegrid /]# cd /settings/network_connections/ETH0
[admin@nodegrid ETH0]# set ipv4_mode=static
[+admin@nodegrid ETH0]# set ipv4_address=10.0.0.10
[+admin@nodegrid ETH0]# set ipv4_bitmask=24
[+admin@nodegrid ETH0]# set ipv4_gateway=10.0.0.1
[+admin@nodegrid ETH0]# show
name: ETH0
type: Ethernet
ethernet_interface = eth0
description =
connect_automatically = yes
set_as_primary_connection = yes
enable_lldp = no
ipv4_mode = static
ipv4_address = 10.0.0.10
ipv4_bitmask = 24
ipv4_gateway = 10.0.0.1
ipv4_dns_server =
ipv4_dns_search =
ipv4_default_route_metric = 90
ipv4_ignore_obtained_default_gateway = no
ipv6_mode = address_auto_configuration
ipv6_dns_server =
ipv6_dns_search =
ipv6_default_route_metric = 90
ipv6_ignore_obtained_default_gateway = no
[+admin@nodegrid ETH0]# commit

7 Configure serial, network & USB devices

Note: Your GSR will respond over the network at 192.168.160.10 if your DHCP server fails or is unavailable.

Note: To check your current IP address, connect to the GSR console port and hit Enter at the login prompt until you see the IP address of ETH0 interface.

To configure the GSR for the first time via Network:

a) Open a web browser (HTTP/S) and enter the GSR IP address in the address field. Or start an SSH session to your GSR’s IP address.

b) Log in to your GSR as admin.

c) Set your GSR basic configuration:

  • Security

    • Security, Services page: Select the desired services and Ports, cryptographic protocols and cipher suite levels. Click Save when finished.

    • Authentication page: add your Remote Authentication servers (AD, LDAP, Tacacs+, Radius and/or Kerberos). Click Save when finished.

    • Authorization page: create users groups, set profiles and assign devices. Click Save when finished.

  • Network

    • Network Settings tab: Set your desired Network parameters. Click Save for each submenu.

    • Network Connections tab: Set your desired Network Interfaces parameters. Click Save for each submenu.

  • Serial and USB ports

    • Managed Devices tab: Enable and configure your desired serial and USB ports.

  • Change Admin Password
    At any time, click admin@domain.comin the upper right corner of your screen and click “Change Password” to change your system password. Click Save when finished.

Congratulations!

Your Nodegrid Gate SR is now configured and ready to accept users and connections to its ports and interfaces.

8 Additional Configuration

NOTE: We recommend that you set up a new Administrator account (in admin group with full privileges) and use the new account instead of the default admin account.

Add New Users
Click Security tab, Local Accounts, Add, set options, Save.

Alerts & logging
Set and send alerts by email, SMS, and/or SNMP.

Power
Control network attached PDU power strips and server, network and storage devices.

For advanced configuration options, please refer to the Nodegrid User Guide.

9 Get technical updates

To automatically receive future firmware updates and technical information, sign up here:
www.zpesystems.com/the-loop/



By installing, copying, or otherwise using this device, you agree to be bound by the terms of the licensing, maintenance and sale agreements set forth on www.zpesystems.com/docs/legal. If you do not agree to the terms of those agreements, do not install or use the Hardware and/or Software Product(s).


Was this article helpful?

ESC

Eddy AI, facilitating knowledge discovery through conversational intelligence